Aritech ATS3000 Manuel d'utilisateur télécharger pdf (Page 4)

ATS2000/3000/4000/4500 Quick Programming Guide

1. QUICK PROGRAMMING GUIDE

1. Defaulting the panel to factory

defaults (using the ‘Kill’ jumper)

When installed, the control panel needs to be defaulted

to factory defaults. This option resets all programming to

the factory default. All programming will be erased and

all options will have the standard values. (Real time

clock will be reset).

Follow the next steps:

1. Remove all power to the control panel (mains and

battery)

2. Shorten the “KILL” jumper

3. Wait 30 seconds

4. Open the “KILL” jumper

The panel is now back to factory defaults.

2. Powering up the panel

On the initial power-up:

• The ATS control panel LED’s should indicate:

L1 - Slow flashing

Comms Tx - Rapid flashing

Comms Rx - Rapid flashing (If RAS 1 connected

and functional)

• The Master LCD Arming Station (RAS 1) should

have all area LED ON and the LCD should display

the name "Aritech Systems" followed by details of

the Arming Station software version.

A LCD RAS will also prompt you to Press the [MENU*]

key.

Press the [MENU*] key followed by [ENTER]. The

normal LCD display message shown below appears:

If there is a system condition, it is displayed on the top

line.

If the Master RAS powers up with no LED ON and there

is no LCD display, then no power has been applied to

the RAS. If the Master RAS powers up with all the LED

flashing, the LCD reads "System Fault" and the control

panel conditions as described above are correct, then:

The system databus cabling must be faulty, or

The Arming Station address has been incorrectly set

(RAS 1 = All dipswitches OFF).

3. Disarming the system

You must disarm the system before you can use the

Installer Menu.

To disarm the system

Press 1 1 2 2 (Manager PIN code), [OFF] followed by 0

(select all areas) and then [ENTER].

If you are unable to disarm the system using the

Manager PIN Code and the [OFF] key, then you might

need to default the panel.

4. Defaulting the panel to factory

defaults (using Menu 14)

99-ALL – This option resets all programming to the

factory default. All programming will be erased and all

options will have the standard values. (Real time clock

will not be affected).

For other options refer to the ATS2000/3000/4000/4500

programming guide

To default the panel programming settings

1. Enter [Menu*] 1 2 7 8 and press [ENTER] to access

the ATS menu.

2. Press 19 [ENTER] to access the programming

menu. The following display appears:

3. Press * to access the Advanced Menu

4. Press 14 [ENTER] to access the Default menu

5. Press 99 [ENTER]. Panel is now defaulted.

5. Entering the ATS menu

Enter [Menu*] 1 2 7 8 and press [ENTER]. The following

display appears:

You can now enter the desired menu number.

See the programming and manager guide

6. Entering the programming menu to

program the system

To enter to the programming menu

1. Press [MENU*] 1 2 7 8 and press [ENTER] to

access the ATS menu.

2. Press 19 and [ENTER] to access the programming

menu. The following display appears:

0-Exit, ENTER-Down, *-Up

0-Exit, Menu:

Simple/Advanced Menu

* - Advanced

There Are No Alarms In This Area

Code:

h L

J17 - Power System earth (see details page 4)12 V battery.

J14 - Auxiliary powerJ13 Sirens/Strobe ConnectionExternal 8 Ohm siren speaker or sirene

1K resistor must be fitted if external siren not connected.Internal 8 Ohm siren speaker 12 V strobeJ3 - Comms and panel tamper wiring

System databusNormally closed front panel tamper contactNormally closed rear panel tamper contact

J9 - BellJ2 to J6 Zone wiringNormally Closed Alarm Contact

Normally Closed Tamper contactJ7 ATS1202 Zone expansion J8 - CLKOUT (ATS1810/1820)

+12V Output boardJ11 Computer/printer expansion J18 Serial connection (RS232)

J20 ISDN/Audio Interface J15/J19 RJ45 PTT connector (not fitted)J16 PSTN Line connection

EPROM (factory fitted)Flash/RAM or IUM (optional)ISP. Circuit programming connector, used to program the CPLD (factory used)

Test 1 Use for resetting the Master Engineer code.Test 2 Factory use onlyTo be used for ATS1202 (only with ATS3000)





S+S-S+S-+-







1211

TH1TH3TH5TH2TH4

NEGCPOS

J11

HEPR

ABAXBXEA

TST1TST2

+12V

-1

KILL

12V RX TX

1413

161

1717

272

rvi

ect

n -

l P

ATS3000/4000J18DB25Db9

12VRX.............................TX23TX.............................RX32

0V..............................GND75

1011

121314

151617

181920

212223

242526

272829

303132

3334

345

Kill - F

acto

l wh

ted

Transformer AC connection

h L