Aritech CS175 Guide d'installation

CS175-275-575-875 LCD/LED Installation Guide Document Version 2.4 : July 2003

10 CS175-275-575-875 Installation Guide 3 DEFAULT COUNTRY CODES Country Country code User code Installer code Download Access Code Baltic states 03

100 CS175-275-575-875 Installation Guide Terminal Description POS Connect to the KP POS terminal of the CSx75. Current draw is 30 mA. COM Connect to

CS175-275-575-875 Installation Guide 101 17.4.2 Programming the zone configuration and partition All zones are programmed via the CSx75 panel and ke

102 CS175-275-575-875 Installation Guide Location 194 Starting zone (one segment, ND) Segment 1 0 Starting zone is zone 1 1 Starting zone is zone

CS175-275-575-875 Installation Guide 103 " For Belgium the following parameters must be configured: Segment 1: Number of minutes, for non-fire t

104 CS175-275-575-875 Installation Guide Transmitter Action Door/Window Activate tamper switch by removing the cover. Door/Window with external cont

CS175-275-575-875 Installation Guide 105 2. The keypad prompts you to enter a module number. 3. Enter the module number and press #. The module num

106 CS175-275-575-875 Installation Guide 18 CS216 HARDWARE ZONE EXPANDER The CS216 is a microprocessor-controlled 16-zone expander for the CSx75 contr

CS175-275-575-875 Installation Guide 107 Starting Zone Number Module Number DIP Switch 1 DIP Switch 2 DIP Switch 3 DIP Switch 4 DIP Switch 5 9 23 On

108 CS175-275-575-875 Installation Guide Terminal Description Connector on the left side DATA Connect to the KP DATA terminal of the CSx75. (See the

CS175-275-575-875 Installation Guide 109 19 CS534 AUDIO BOARD The CS534 is a two-way audio (voice) communicator for the CSx75 alarm panel. Once the a

CS175-275-575-875 Installation Guide 11 4 INSTALLATION GUIDELINES This installation manual details the installation and programming of the CSx75 usin

110 CS175-275-575-875 Installation Guide 19.1.2 Call back mode If programmed for this mode, the CS534 starts a timer when the control panel releases t

CS175-275-575-875 Installation Guide 111 SPK+ SPK- Connect to the speaker(s). Maximum speaker wire run: 1000’ (300m). Minimum speaker rating: 5 Watt

112 CS175-275-575-875 Installation Guide before the time-out period (location 3, segment 1), the system returns to the stand-by mode and waits for a n

CS175-275-575-875 Installation Guide 113 99 Terminates session and returns to the stand-by mode and waits for a new trip. MICROPHONE CONTROL (ZONIN

114 CS175-275-575-875 Installation Guide Tone Description One high tone for 100 mS Time remaining indicator “A “ One mid tone for 100 mS Time rema

CS175-275-575-875 Installation Guide 115 • On: listen-in only mode: this allows the central station to listen to the activity at the premises. • Of

116 CS175-275-575-875 Installation Guide Seg 3 Call back windows timer (Default = 5 minutes) • Determines the amount of time, in one-minute increment

CS175-275-575-875 Installation Guide 117 Location 5 Programming X-10 address for output 1 (two segments, ND) " An X-10 interface module, such

118 CS175-275-575-875 Installation Guide 20 CS507 OUPUT EXPANDER BOARD The CS507 is an auxiliary module used to expand the capabilities of the CSx75 c

CS175-275-575-875 Installation Guide 119 3 Auxiliary power connection 7 X–10 Supervision LED 11 Relay 4 Keypad bus connection 8 X-10 Connection 2

12 CS175-275-575-875 Installation Guide through the on-board electronic output, must be of SELV (Safety extra-low voltage) operating circuit. • Use a

120 CS175-275-575-875 Installation Guide Terminal Description Vout This terminal can supply up to 100 mA fused separate from the power in the control

CS175-275-575-875 Installation Guide 121 20.3 Programming the CS507 20.3.1 Programming the output configuration and partition Location 0 Programmin

122 CS175-275-575-875 Installation Guide  If set to follow condition, these events is 1 second.  Events 46 and 47 require RX8i4 - RX16i4 wireless

CS175-275-575-875 Installation Guide 123 4 On: the event follows schedule 4. 5 On: the event follows schedule 5. 6 On: the event follows schedule

124 CS175-275-575-875 Installation Guide Location 32 Programming the opening time for schedule 1 (two segments, ND) Segment 1 Program the hour of the

CS175-275-575-875 Installation Guide 125 " The zone/user for the corresponding output must be "0" to use this location. The last bit o

126 CS175-275-575-875 Installation Guide Location 75 Authorizing users 71 to 80 When activating outputs with a user code, this location can be used

CS175-275-575-875 Installation Guide 127 21 CS586 RS232 INTERFACE The CS586 is a low cost add-on module that fits neatly into any CSx75 system enclo

128 CS175-275-575-875 Installation Guide Signal Name CS175 ------ PC Jumper number Pin number A position Pin number B position TXS - > J8 2 3

CS175-275-575-875 Installation Guide 129 Location 0 Programming the option flag (one segment, FSD) The CS586 protocol can operate in one of two poss

CS175-275-575-875 Installation Guide 13 defaulting and programming the control panel and the modules, adding users and setting authority levels. 7.

130 CS175-275-575-875 Installation Guide 22 CONTROL PANEL PROGRAMMING WORKSHEETS Factory defaults for segments are in bold italics and Quick Start loc

CS175-275-575-875 Installation Guide 131 Seg#1 (Circle numbers to program) Seg#2 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 26 Dial attempts for phone

132 CS175-275-575-875 Installation Guide 36 Zones 1-8, zone types 5-4-1-1-1-1-1-1 37 Zones 1-8, partition selection (Segment 1=zone 1 to segmen

CS175-275-575-875 Installation Guide 133 Seg#4 (36) 1 Seg#5 (37) 1 Seg#6 (38) 1 Seg#7 (39) 1 Seg#8 (40) 1

134 CS175-275-575-875 Installation Guide 1 2 3 4 5 6 7 8 On: disables on-board 8 zones. On: force default configuration for zone types to be used.

CS175-275-575-875 Installation Guide 135 Seg#2 (Circle numbers to program) 1 2 3 4 5 6 7 8 Enables Go to program code for partition #1. Enables

136 CS175-275-575-875 Installation Guide 67 Days of the week each partition is open Segments 1 2 3 4 5 6 7 8 Sunday Monday Tuesday Wednesday T

CS175-275-575-875 Installation Guide 137 100 Expander trouble restore 0-0 101 Fail to communicate 0-0-0 102 Log full 0-0-0 103 Autotest 0-0-0

138 CS175-275-575-875 Installation Guide Seg#5 – Reserved The defaults listed in the characteristic locations below represent the three segments of

CS175-275-575-875 Installation Guide 139 166 Characteristic select 167 SIA code: Group 11 168 4/2 alarm code Seg#1-2-3: 0-0-0 169 4/

14 CS175-275-575-875 Installation Guide 4.4 Installation schematic Connect all modules and keypads to the keypad bus Set module DIP switches and recor

140 CS175-275-575-875 Installation Guide Seg#1-2: 0-0 202 Characteristic select 203 SIA Code: Group 20 204 4/2 alarm code Seg#1-2-

CS175-275-575-875 Installation Guide 141 Seg#3 (51) 1 Seg#4 (52) 1 Seg#5 (53) 1 Seg#6 (54) 1 Seg#7 (55) 1

142 CS175-275-575-875 Installation Guide Segments Part#1 Part#2 Part#3 Part#4 Part#5 Part#6 Part#7 Part#8 Seg#1 (89) 1 Seg#2 (90) 1

CS175-275-575-875 Installation Guide 143 Seg#4 (124) 1 Seg#5 (125) 1 Seg#6 (126) 1 Seg#7 (127) 1 Seg#8 (128

144 CS175-275-575-875 Installation Guide Segments Part#1 Part#2 Part#3 Part#4 Part#5 Part#6 Part#7 Part#8 Seg#1 (161) 1 Seg#2 (162) 1

CS175-275-575-875 Installation Guide 145 23 APPENDIX 1: REPORTING FIXED CODES IN CONTACT ID AND SIA This table lists the event codes sent for the fol

146 CS175-275-575-875 Installation Guide Report Contact ID SIA Zone bypass (zone number) 570 *B Bypass restore (zone number) 570 *U Near Alarm (A/B

CS175-275-575-875 Installation Guide 147 24 APPENDIX 2: REPORTING ZONE CODES IN CONTACT ID AND SIA The CSx75 can report SIA level 1 transmissions to

148 CS175-275-575-875 Installation Guide SIA Contact ID 20 ZA Freeze Alarm 159 Low Temp

CS175-275-575-875 Installation Guide 149 25 APPENDIX 3: OVERVIEW OF MODULE NUMBERS Every keypad, expansion module and wireless receiver module has a

CS175-275-575-875 Installation Guide 15 INSTALLING THE CONTROL UNIT 4.4.1 CS575M/CS875M (large metal housing) This large metal housing can be used wi

150 CS175-275-575-875 Installation Guide Address & DIP switch setting 24 (Switch 1 & 2 on) 28 (Switch 1, 2 & 3 on) 25 (Switch 3 on)

CS175-275-575-875 Installation Guide 151 26 APPENDIX 4: SERVICE MESSAGES Message Explanation Control Over-current A short circuit of a control pan

152 CS175-275-575-875 Installation Guide 27 GLOSSARY 24-hour zone This zone remains armed the whole time unless inhibited by forced arming. It reports

CS175-275-575-875 Installation Guide 153 Automatic arming If programmed, the CSx75 auto arms at a specified time. At this time, the keypad beeps for

154 CS175-275-575-875 Installation Guide Cancel If enabled, the CSx75 sends a cancel report if when the system is disarmed. Dialler Delay must be enab

CS175-275-575-875 Installation Guide 155 Entry-guard A unique low level arming mode that reduces the most common source of false alarms. When armed,

156 CS175-275-575-875 Installation Guide Force arming Arms the security system when a number of zones are open without inhibiting each one individuall

CS175-275-575-875 Installation Guide 157 LED extinguish This feature extinguishes all LEDs on the keypad, except the Power LED, after 60 seconds with

158 CS175-275-575-875 Installation Guide Silent exit option The exit delay can be silenced by pressing -Exit before arming the control panel or when

CS175-275-575-875 Installation Guide 159 Two-call answering machine defeat If enabled, two telephone calls must be made to the premises to defeat an

16 CS175-275-575-875 Installation Guide 9. Add the pillars for the CS507 output module or CS216 input expander or CS7001 to the box. 10. Mount the C

160 CS175-275-575-875 Installation Guide 28 TECHNICAL SPECIFICATIONS Operating power Input 230 VAC ± 10% - 50 Hz ± 10% Fuse 230 V F315 mA, 20x5 Operat

CS175-275-575-875 Installation Guide 161 Static Impulse Single loop 4k7: Disarmed Quiet Short Armed Change status Open: No reaction

162 CS175-275-575-875 Installation Guide 29 TASKS SUMMARY Command Task Master User Code: 1122 User Code Installer Code: 1278  0 Set tone No code

CS175-275-575 Manual 163 30 INDEX 25 VA transformer...59 2-wire smoke detectors...

164 CS175-275-575-875 Installation Guide access ... 7 installer...

CS175-275-575 Manual 165 Number of rings to answer...55 Numerical data...

166 CS175-275-575-875 Installation Guide Walk test mode ...60, 134 Wireless transmitters setting options and par

CS175-275-575 Manual 167

CS175-275-575-875 Installation Guide 17 4.4.2 CS275/CS575/CS875 (polycarbonate housing) This polycarbonate housing can be used with the CS275, CS575

18 CS175-275-575-875 Installation Guide 8. Flip down the PCB mounting tray. 9. Attach the pillars for the CS535 voice module to the board. 10. Atta

CS175-275-575-875 Installation Guide 19 14. Drill 0.3 mm holes for the card guides in the box. 15. Place the card guide on the box. 16. Screw in the

98/482/EC declaration (Applies to products that have the CE mark attached) This equipment has been approved in accordance with Council Decision

20 CS175-275-575-875 Installation Guide Steps 1. Open the box. 2. Wire the panel. 3. Attach the pillars for the CS534 listen-in module or CS535 vo

CS175-275-575-875 Installation Guide 21 6. Add the pillars for the CS216 input expander or CS507 output expander to the main board. 7. Mount the

22 CS175-275-575-875 Installation Guide 4.5 Control unit wiring diagram: CS-175 1 Zones 1-4 6 External sounder 11 Serial expansion

CS175-275-575-875 Installation Guide 23 4.5.1 Inputs and outputs CS175 DATA Communication/Expander data (0101) (Including Keypad) AUX + Communi

24 CS175-275-575-875 Installation Guide 4.6 Control unit wiring diagram: CS-275 1 Zones 1-6 7 Open collector 1 12 Serial expansion 2

CS175-275-575-875 Installation Guide 25 4.6.1 Inputs and outputs CS275 DATA Communication/Expander data (0101) (Including Keypad) AUX + Communica

26 CS175-275-575-875 Installation Guide 4.7 Control unit wiring diagram: CS-575 and CS-875 1 Zones 1-8 7 Relay 1 12 Serial expansion

CS175-275-575-875 Installation Guide 27 4.7.1 Inputs and outputs CS575 and CS875 DATA Communication/Expander data (0101) (Including Keypad) AUX +

28 CS175-275-575-875 Installation Guide 5 LCD - LED KEYPAD Power (green) When lit, the system is powered up. Ready (green) The Ready LED is on w

CS175-275-575-875 Installation Guide 29 Chime Press to turn the chime on and off. # Hash key Press to access modules and locations. * Star Press to

CS175-275-575-875 Installation Guide 3 CONTENTS 1 Introducing the CSx75 system ...

30 CS175-275-575-875 Installation Guide 5.3 Wiring the keypad The keypad should be wired to the control unit as follows. +-Com13.8V0101DataAux+ CSx75

CS175-275-575-875 Installation Guide 31 In a star network, each keypad is wired back separately to the control unit terminals. 5.4.3 Star and multi

32 CS175-275-575-875 Installation Guide 6 WIRING ZONES 6.1 General The control unit inputs are set up as standard EOL (4K7) freely programmable zones.

CS175-275-575-875 Installation Guide 33 7 WIRING SOUNDERS 7.1 Wiring a sounder with EOL protection Any zone can be used. It should be programmed as

34 CS175-275-575-875 Installation Guide 7.3 AS271 CSx75 AS271 1 Tamper 4 0 V speaker 2 Tamper 5 0 V beacon (AS271 only) 3 +13.8 V

CS175-275-575-875 Installation Guide 35 7.4 AS290/390 CSx75 AS290/AS390 1 Piezo 4 Beacon 7 GND 2 Piezo 5 Tamper 8 +13.8 V 3 Beacon 6

36 CS175-275-575-875 Installation Guide 8 WIRING FIRE DETECTORS 8.1 General If you need to drive more than one 4-wire fire detector, you may need to u

CS175-275-575-875 Installation Guide 37 8.1.3 4-wire fire detector (CS175) DB702 + DP721R DB702 + DP721R CS175 COMZ1AUX+COMSMOKE112

38 CS175-275-575-875 Installation Guide 9 WIRING THE OUTPUTS 9.1 Wiring the outputs The amount and type of available outputs is different per panel t

CS175-275-575-875 Installation Guide 39 CS175

4 CS175-275-575-875 Installation Guide 10.2.9 Assigning authority level ...

40 CS175-275-575-875 Installation Guide 10 PROGRAMMING THE SYSTEM 10.1 Enrolling modules and keypads The CSx75 can automatically find and store in its

CS175-275-575-875 Installation Guide 41 1. Press 93. 2. Enter a Go to program code. 3. Set the keypad features listed in the following table. Pre

42 CS175-275-575-875 Installation Guide 10.2.4 Setting elapsed increments since last autotest 1. Press 95. 2. Enter a Go to program code. 3. Enter

CS175-275-575-875 Installation Guide 43 4. Enter the new user code for the selected user. If you are changing the current code, use the scroll keys

44 CS175-275-575-875 Installation Guide 6. To remove access to a partition, press the partition number on the keypad. The partition is marked with a

CS175-275-575-875 Installation Guide 45 Scroll keys Press to scroll through letters and lists on the keypad display. Stay Press to insert a space

46 CS175-275-575-875 Installation Guide 2. Enter a Go to program code. 3. Enter the keypad number (1-8). The Bypass LED and the Service LED blink a

CS175-275-575-875 Installation Guide 47 2. Enter a Go to program code. 3. Enter [100's digit] -[10's digit]-[1's digit]-[#] and pres

48 CS175-275-575-875 Installation Guide Steps 1. Press 6. 2. Enter a master user code. The keypad prompts you to enter a user number. 3. Enter a t

CS175-275-575-875 Installation Guide 49 LED 2 is lit, the user can access partition 2. Press 2 to deny the user access to the partition and to turn o

CS175-275-575-875 Installation Guide 5 16.4 Programming the RX8i4-16i4 ...

50 CS175-275-575-875 Installation Guide 11 PROGRAMMING MODULES AND LOCATIONS 11.1 Parts of the system The system is divided into modules, locations,

CS175-275-575-875 Installation Guide 51 • Several features can be selected from within one segment. For instance, if you want all eight features of a

52 CS175-275-575-875 Installation Guide 12 PROGRAMMING THE PANEL 12.1 Default programming For most routine installations, the default programming allo

CS175-275-575-875 Installation Guide 53 12.5 Defining the country code 1. Enter programming mode as described in Entering programming mode on page 5

54 CS175-275-575-875 Installation Guide • To program a module, enter its address and press #. See Selecting a module to program on page 52 for more in

CS175-275-575-875 Installation Guide 55 • To program a module, enter its address and press #. See Selecting a module to program on page 52 for more i

56 CS175-275-575-875 Installation Guide 13 PROGRAMMING WITH UP/DOWNLOAD SOFTWARE 13.1 General You can program the CSx75 using the LED keypad, the LCD

CS175-275-575-875 Installation Guide 57 14 CONTROL PANEL PROGRAMMING LOCATIONS Location Description 0 Country code Phone set up 1 Phone prefix 2 P

58 CS175-275-575-875 Installation Guide Location Description 65 Opening time 66 Closing time/automatic arming time 67 Days of the week each partition

CS175-275-575-875 Installation Guide 59 Location Description 152 4/2 alarm code group 7 153 4/2 restore group 7 154 Group 7 zone type characteristi

6 CS175-275-575-875 Installation Guide 21.2.1 LED Indications...

60 CS175-275-575-875 Installation Guide Location Description 232 Partition select, zones 105-112 233 Zones 113-120 zone type 234 Partition sele

CS175-275-575-875 Installation Guide 61 Location 0 Country code (one segment, ND) This location contains the country code which sets the specific co

62 CS175-275-575-875 Installation Guide Location 3 Account code for phone #1 (six segments, ND) This location contains the account code sent when pho

CS175-275-575-875 Installation Guide 63 3 Opening and closings 4 Zone bypass and bypass restores 5 Zone trouble and trouble restores 6 Power fail

64 CS175-275-575-875 Installation Guide Tone dialling pager or Siren Tone formats. The factory default is 8. Location 27 Reserved Location 28 Dial

CS175-275-575-875 Installation Guide 65 Location 33 Download call back number (16 segments, ND) If a telephone number is programmed in this locatio

66 CS175-275-575-875 Installation Guide 7 Reserved 8 On: enables silent exit always. Segment 3 1 On: enables opening and closing reports. 2 On: en

CS175-275-575-875 Installation Guide 67 Location 36 Zone type, zones 1 to 8 (eight segments, ND) Zones can be programmed to be one of twenty differe

68 CS175-275-575-875 Installation Guide 8 Partition #8 Location 38 Zone type, zones 9 to 16 (eight segments, ND) This location contains the zone ty

CS175-275-575-875 Installation Guide 69 Location 47 Partition select, zones 41 to 48 (eight segments, FSD) This location is used to select the part

CS175-275-575-875 Installation Guide 7 1 INTRODUCING THE CSX75 SYSTEM The CSx75 range represents a new approach to security systems design. It is fle

70 CS175-275-575-875 Installation Guide Location 51 System options (five segments, FSD) This location is used to enable various system feature and r

CS175-275-575-875 Installation Guide 71 5 On: enables end download report. 6 On: enables sensor low battery report. 7 On: enables sensor missing r

72 CS175-275-575-875 Installation Guide and 99 (answer incoming call for download) functions. 3 Reserved 4 Enable walk-test mode 5-8 Reserved Lo

CS175-275-575-875 Installation Guide 73 Location 57 Auxiliary output 1 to 4 partition selection (four segments, FSD) This location is used to selec

74 CS175-275-575-875 Installation Guide Data Event Data Event 1  Fire alarm 22 Disarmed state 2  24-hour alarm 23 Ready 3  Trouble alarm 24

CS175-275-575-875 Installation Guide 75  Events 49 and 50 require RX8w8, RX16w8, RX8i4 or RX16i4 wireless receivers to operate.  If set to the fol

76 CS175-275-575-875 Installation Guide Location 65 Opening time (two segments, ND) This location contains the time, in 24-hour format, that the CSx7

CS175-275-575-875 Installation Guide 77 2 Auto arming on Monday 3 Auto arming on Tuesday 4 Auto arming on Wednesday 5 Auto arming on Thursday 6

78 CS175-275-575-875 Installation Guide Communicator Code Location Number of Segments Box trouble restore 79 2 Siren tamper 80 3 Siren tamper

CS175-275-575-875 Installation Guide 79 Communicator Code Location Number of Segments End download 108 3 Locations 109 to 121 Reserved Locatio

8 CS175-275-575-875 Installation Guide • Two partitions. • Integrated fire, access, verification and input/output modules. • Franklin 4+2, SIA, 200 ba

80 CS175-275-575-875 Installation Guide 8 On: DTMF. Location 127 SIA code group 1 (one segment, ND) This location contains the event code sent for a

CS175-275-575-875 Installation Guide 81 6 On: the zone type is included in the group shunt. 7 On: the zone type is force armable. 8 On: the zone t

82 CS175-275-575-875 Installation Guide Description 1 2 3 4 5 6 7 8 9 10 4/2 restore 169 173 177 181 185 189 193 197 201 205 Characteristics

CS175-275-575-875 Installation Guide 83 3 Log event message 4 Keypad message received 5-8 Reserved Location 211 CS586 command/request enable (fou

84 CS175-275-575-875 Installation Guide 6 Primary keypad function without PIN 7 Secondary keypad function 8 Zone bypass toggle Location 212 LCD ke

CS175-275-575-875 Installation Guide 85 Location 221 Zone type, zones 81 to 88 (eight segments, ND) This location contains the zone type for zones

86 CS175-275-575-875 Installation Guide Location 231 Zone type, zones 105 to 112 (eight segments, ND) This location contains the zone type for zones

CS175-275-575-875 Installation Guide 87 Location 241 Zone type, zones 145 to 152 (eight segments, ND) This location contains the zone type for zone

88 CS175-275-575-875 Installation Guide 15 USING PARTITIONED SYSTEMS Your system can be divided up so that it works in different ways in different are

CS175-275-575-875 Installation Guide 89 2. The numbers on the top line represent the disarmed areas the code can access. The numbers on the bottom l

CS175-275-575-875 Installation Guide 9 2 DEFAULT CODES Default installer code 1278 when using a four-digit code 127800 when using a six-digit code Lo

90 CS175-275-575-875 Installation Guide All keys and functions entered affect this individual partition only. The LEDs and display represent the stat

CS175-275-575-875 Installation Guide 91 16 SETTING UP RF ZONES – RX8I4-16I4 The RX-Series receiver modules add wireless capabilities to a CSx75 contr

92 CS175-275-575-875 Installation Guide Module Number DIP Switch 1 DIP Switch 2 DIP Switch 3 DIP Switch 4 34 On On On Not Used 33 Off On On Not

CS175-275-575-875 Installation Guide 93 Frequency 433 MHz for the RX8i4 and RX16i4 Current draw 20 mA Maximum Operating temperature 0 to 49 °C Dimens

94 CS175-275-575-875 Installation Guide Location 1 Wireless sensor 1 characteristics (two segments, FSD) This location defines the characteristics

CS175-275-575-875 Installation Guide 95 Location 194 Starting zone (one segment, ND) Segment 1 0 Starting zone is zone 1 1 Starting zone is zone 9

96 CS175-275-575-875 Installation Guide The following guidelines should be followed when programming the RX8i4-16i4 modules. • When a transmitter is

CS175-275-575-875 Installation Guide 97 Repeater Press and then release the tamper switch. 16.4.4 Deleting transmitters The following steps describe

98 CS175-275-575-875 Installation Guide 17 SETTING UP RF ZONES – RX8W8-16W8 The RX-Series receiver modules adds 868 MHz wirelless capabilities to a CS

CS175-275-575-875 Installation Guide 99 17.1 Setting the DIP switches Decide the starting zone of each zone expander. The starting zone must be on a