Aritech ATS4000 Manuel de service télécharger pdf (Page 29)

ATS Designers Guide 29

2.2 System equipment power consumption.

Devices equipped with a power supply – control panels, and some DGP – have safety

measures which prevent excessive battery discharging, switching them off if the voltage

drops below 10.5V. For other devices, the minimum voltage required to operate correctly

has been gathered in table Table 7-9 placed in the last chapter of the manual. The values

for equipment connected to devices equipped with a power supply are only for orientation

purposes.

Some devices have characteristic current consumption values depending on the

connected equipment. In the table below the current consumption is given for the device

with connected equipment. A detailed list of device parameters in different working

conditions are given in chapter 7 of the manual in table Table 7-9.

Table 2-4 Characteristic power requirements for the ATS devices.

Current con. mADevice

Connected

equipment

Description

Max. Average

ATS1100 - Keypad, 2*16 characters LCD/8 zone LEDs 185 73

ATS1105 -

Keypad, 2*16 characters LCD /8 zone LEDs with

Wiegand reader interface.

185 78

ATS1105+ ATS1410

ATS1105 manipulator with a magnetic card reader

connected

195 150

ATS1110 - Keypad, 2*16 characters LCD/16 zone LEDs 95 32

ATS1111 - Keypad, 4*16 characters LCD/16 zone LEDs 95 32

ATS1115 -

Keypad, 2*16 characters LCD/16 zone LEDs with inbuilt

ATS card reader.

165 86

ATS1116 -

Keypad, 2*16 characters LCD/16 zone LEDs with inbuilt

ATS card reader.

169 86

ATS1151 - LED keypad (3 diodes) in metal housing, no LCD

45 34

ATS1155 -

Outdoor, vandal-proof keypad (metal), 3 diodes,

detached electronics

70 70

ATS1156 -

LED Manipulator (3 diodes) in metal housing with

ATC600 magnetic card reader

45 39

ATS1170 - Wiegand reader interface (single door controller) – PCB 45 32

ATS1170+ ATS1190 Interface with a proximity card reader connected. 95 65

ATS1190 - Proximity reader (does not require an interface) 50 29

ATS1192 -

High resistance proximity reader (does not require an

interface) indoor/outdoor use

50 29

ATS1202 - 8 zones module for expander and control panel- PCB 10 9

ATS1210/11 - 8 zones and 8 outputs expander 53 50

ATS1210/11+ ATS1810 ATS1210 with 4 relay outputs module connected 130 70

ATS1210/11+ ATS1811 ATS1210 with 8 relay outputs module connected 225 110

ATS1210/11+ ATS1820

ATS1210 with 16 open collector outputs module

connected

90 38

ATS1220 - 4 zones and 8 outputs expander 53 45

ATS1230 - 433MHz wireless device receiver

ATS1290 - Point ID addressable sensor expander. 154 50

ATS1740 - Isolator/ RS485 bus repeater - PCB 90 60

ATS1741 - RS485 / RS232 bus converter- PCB 100 100

ATS1742 - RS485 bus loop interface – PCB 86 86

ATS1743 - Fibre-optical bus converter- PCB 60 36

ATS1810 - 4 relay NO/NC outputs module – PCB 60 1

ATS1811 - 8 relay NO/NC outputs module – PCB 170 20

ATS1820 - 16 open collector outputs module – PCB 50 20

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 82 83

Commentaires sur ces manuels

Pas de commentaire

Aritech ATS4000 Manuel de service Page 29

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Aritech ATS4000